How To Set Up Motorola Router

4G LTE Cellular Modem plus AC1900 WiFi Router
Model ML2410
Quick Start Guide

Packaged with your ML2410

Para una Guía de Inicio Rápido en español, por favor vaya a www.motorolanetwork.com/ML2410ir

Allow'due south go started

To use your ML2410 modem/router you demand an activated micro-SIM (3FF format) which you normally receive from your mobile broadband service provider. If instead, you use a nano-SIM card (used by about phones today), you will need a SIM Carte Adapter. SIM card adapters are bachelor from Amazon and other retailers.
Note: If you want to provide cellular backup to an existing cablevision modem or Internet connexion, we recommend setting upward and testing the cellular connection offset and then changing the configuration to enable cellular backup.

First, insert the SIM card. Remove the battery cover on the ML2410'southward back panel to access the SIM slot. Using a Phillips head screwdriver, remove the screw from the battery embrace. Remove the battery cover and insert the SIM. The copper side of your SIM should be facing inwards and the notch in the SIM should be facing up. Replace the battery cover when finished.
Next, attach the 2 LTE Antennas to the ML2410 by screwing them finger-tight into the 2 gold connectors located on the back of the unit.
Now, connect the supplied ability adapter between the ML2410'due south power jack and an electrical outlet. The ML2410 volition ability upwards and the ability light on the front of the unit of measurement will turn dark-green. If the power light does not turn on, check that the On/Off button on the dorsum panel is On. Await for the Prison cell Status light to plow on. This may take up to 2 minutes. If the Jail cell Status light does not turn on, please see the Troubleshooting Tips at the end of this QuickStart.

If y'all want to apply the ML2410 as cellular backup continue below, otherwise skip ahead to Connect Your Devices to configure your wireless network.

Using the ML2410 for Cellular Backup

If you wish to use the ML2410 every bit a fill-in pick for your principal Internet connection, you should have first installed information technology as a cellular modem above. And then follow these steps.

Connect the ML2410'south yellowish Ethernet cable between the ML2410'due south WAN port and the Ethernet port of a cable modem, DSL modem, or fiber optic modem used for Cyberspace access.
Switch the power off on your primary Internet connexion modem now. (For some modem/routers, this requires you to remove a power backup bombardment.) After the modem is off for at least 10 seconds, switch it back on.
(If you removed a backup bombardment, plug the bombardment dorsum in first.)
To configure your ML2410 for cellular fill-in y'all will need to admission the ML2410'south configuration manager.
First, brand a connection:
• For a wired connectedness, plug an Ethernet cable into one of the ML2410's LAN jacks and the other into your reckoner's Ethernet port.
• Or, for a WiFi connection, go into the WiFi setup section for the other device, such as your telephone or calculator (non the ML2410). Then enter the ML2410'due south WiFi Network Proper noun (SSID) and WiFi Password/Key.
The unique factory-set default settings are printed on a label on the bottom of the modem/router.
Side by side, to access the ML2410'due south configuration manager open your Spider web browser. Blazon http://192.168.five.1 in the accost bar and press Enter.
•In the Login dialog box, enter the Login information printed on the lesser label of your ML2410.
• The Bones Setup page will appear. If the Basic Setup page doesn't appear, delight see the Troubleshooting
Tips beneath.
• From the dropdown menu adjacent to Connection Type,select the type of connexion you take. Most users should select DHCP.
• Check the box side by side to Enable Cellular Backup. This will turn on cellular backup in instance your main Internet connection goes downwardly.
• The ML2410 should automatically notice your SIM card and should be configured correctly.

Now you volition Connect Your Devices to configure your wireless network.

Connect Your Devices

The ML2410 allows many devices to share your Internet connection. Devices can connect by using WiFi or past connecting an Ethernet cable into one of the ML2410 Ethernet
ports.
WiFi Wireless
You can connect whatever of your WiFi devices by first going into the WiFi setup section for the device (not the ML2410 router). And then apply the ML2410 router'due south WiFi Network Name (SSID) and WiFi Password/Key. The unique factory-ready default settings are printed on a label on the bottom of the ML2410. If you prefer to use a different network name and password, the MotoManage™ app is an piece of cake way for yous to change your WiFi network name or countersign. For more information on our MotoManage app see the MotoManage section beneath.

Wired Ethernet
You can also connect up to ii smart TV/media players, computers, game stations, or other devices with an Ethernet cablevision between an Ethernet port of the device and either of the LAN jacks on the router. Some devices have a Network Setup section where you specify a wired Ethernet connexion. If you have a problem with a item device, consult its user manual.
In one case y'all've ready upwards a Wireless or Wired Ethernet connection, try to browse the Spider web. If browsing works, Congratulations! Your ML2410 is working.
If your ML2410 is Not working, see Troubleshooting Tips and
We like to help at the end of this Quick Start.

MotoManage™

Nosotros strongly suggest that you download the MotoManage™
App from the Apple App Store or from Google Play to access bones and advanced network control features. The app lets you lot manage your network quickly and easily, and information technology makes it piece of cake to go on your network's original wireless settings
The app includes basic and advanced features which are all available gratuitous of accuse for the first month. After that you will be able to determine whether you'd like to just keep the free features, or whether y'all'd like to also keep the advanced features for a small-scale monthly fee.

Download the MotoManage app on your smartphone or tablet.
Open up the app.
Browse the QR code on the bottom of your ML2410 to gear up your device'southward WiFi network.
Now enjoy the app. You can easily elect to keep your original proper name and password, as we recommend. Plus you lot can hands monitor your Internet usage and WiFi signal strength, become security alerts that assistance protect your network, control Internet access by devices, or set up some bones parental controls.

Your ML2410 must be online for the app to communicate with it.

Front Panel

LIGHT	COLOR	DESCRIPTION
Power	Dark-green or Amber	Dark-green: OFF: Amber: Blinking Bister:	ML2410 power on ML2410 power off ML2410 running on battery Low battery
Cell Condition	Green or Amber	Greenish: Bister: Blinking: Off:	Continued in LTE mode Connected in 3G manner Sending data Non connected
Cyberspace	Dark-green	Green: OFF:	ML2410 is online ML2410 is offline
2.iv GHz WLAN	Greenish	ON: Blinking: OFF:	ii.4 GHz WiFi is enabled Data is flowing WiFi is not enabled
5 GHz WLAN	Dark-green	ON: Blinking: OFF:	v GHz WiFi is enabled Data is flowing WiFi is non enabled
WPS	Green	ON: Blinking: OFF:	WPS connexion successful; turns off after 5 minutes WPS in discovery mode WPS not active

Back Panel

RESET – Resets the ML2410 to manufactory defaults
WPS – WiFi Protected Setup
ANT Main – Master cellular antenna
Pismire DIV – Diversity cellular antenna
USB 3.0 PORT
WAN PORT – Connect to your modem for cellular backup
LAN PORTS – Connect a computer, smart Boob tube/media player, game station, or some other Ethernet-capable device to either of these two LAN ports
ON/OFF push
Ability – Connect the supplied power adapter betwixt the power jack and an electrical outlet
BATTERY – Install optional battery to provide Internet access when the power goes out
SIM SLOT – Located behind the battery encompass. Remove the cover and insert a Micro (3FF) SIM bill of fare

Troubleshooting Tips

I'thousand using cellular as my connexion type and I can't connect to the Internet after installing my ML2410.

Check that the ML2410 is powered on. The power LED on the front panel should exist green. If it is not on and then:
o Bank check that the ability button on the back of the unit of measurement is pushed in.
o Check that the power cable is correctly plugged into the modem and that the other end of the cable is plugged into a working electrical outlet.
Confirm that the modem can talk to the SIM. Log in to the Configuration Manager by typing 192.168.5.ane in the address bar of your browser, go to that address, and enter the Username and Password. The default Username and Password are printed on the lesser of your device. On the bill of fare on the left, click Status and then Cellular. There should be a 19 or 20 digit number next to IMSI. If this number is missing, effort reinserting your SIM. You may need to request a new SIM from your service provider if the modem can't read it.
Verify with your service provider that your account is active.
You may need to set the APN on your modem. Log in to the Configuration Director by typing 192.168.5.one in the accost bar of your browser, go to that address, enter the Username and Password. On the menu on the left, click Basic Setup then
APN. Yous should contact your service provider for the correct
APN. Some mutual APNs are:

Verizon: VZWINTERNET
AT&T: NXTGENPHONE or BROADBAND
T-Mobile: fast.t-mobile.com

For more information on setting APNs please see the full-length user manual at:www.motorolanetwork.com/ML2410manual
My cellular connection seems slow.

You may need to move the ML2410 closer to a window in your house to improve the cellular signal.
During times of high cellular traffic, the bandwidth bachelor to the ML2410 will be limited. This may result in slower speeds than received during non-summit times.
I'm plugging the ML2410'south WAN port into another modem and cannot access the Cyberspace.
Power cycle the modem. This will cause it to asking a new IP address.
Verify that your ML2410's WAN port is configured for DHCP, sometimes called Dynamic Routing, Cable Modem, or
Automatic. Nigh users should utilize DHCP.
Verify that the cable betwixt the router and modem (or Ethernet jack if connecting to an in-building network) is plugged into the router's WAN jack.
Check that the modem you are using is powered up and continued to the Cyberspace. Plug a computer directly into your modem or external network and check that your service is working.
I'm unable to admission the ML2410 when I try to login to the Configuration Manager.
Outset bank check that the ML2410'southward Ability light is on.
The yellow LAN Ethernet jack on the back of the ML2410 has a green LED on it. This LED should be on when the Ethernet cable is plugged in. If it is not on, check that the Ethernet cable is securely plugged into the ML2410 and into your PC. If that doesn't piece of work, your Ethernet cablevision could exist the problem.
Try a different Ethernet cable that you know works.
What if I'g connected over WiFi but my connection seems boring or keeps dropping?
Notation that wireless operation depends on a number of factors. Please keep these things in mind:
Where possible, put the ML2410 in a central identify and so that it'due south not too far away from your other wireless devices.
Don't put the ML2410 close to interference-generating wireless devices such as Bluetooth headsets and stereos, microwave ovens, 2.4 GHz cordless phones and base stations, and WiFi printers.
The ML2410 router provides a powerful wireless signal that can help reach many corners of your house. However, the wireless range can be limited by a multifariousness of problems, including weak wireless clients and challenging building configurations. Many devices, such as phones, that you may utilize to connect to the ML2410 practice not have every bit powerful a wireless signal. Although the ML2410's advanced wireless applied science tin can help improve the performance and range of the devices, often the weaker signal of your other devices tin exist a limiting gene.
Do you have any other questions? A skilful identify to start is our total-length user manual: www.motorolanetwork.com/ML2410manual

Battery Purchase or Replacement

The ML2410 has battery backup circuitry which allows your jail cell modem/router to still function even when your Ac power is lost. The ML2410 typically does not ship with a battery included. Note that in the case of loss of power, the bombardment will provide up to 12 hours of usage. You can control which features are enabled in battery mode. Delight run across the full-length manual at www.motorolanetwork.com/ML2410 for details.
A bombardment is not required for normal operation with Air-conditioning power. If yous want a backup bombardment, you lot can buy one online.
The blazon of backup battery that tin be used with this product is Model 98250 from MTRLC and is labeled BP 15033 22/2150 Southward.

We like to help.
Please visit our Support Website or phone call our support specialists. Our Website has our Motorola Mentor information, and also provides returns and warranty information.
world wide web.motorolanetwork.com/support
Email: [email protected]
Telephone, in the United states of america and near other countries: 800-753-0797 or +ane 617-753-0562
United kingdom: +44 800 023 9083
Espana: +34 900 839 783
Our full-length user manual is available at world wide web.motorolanetwork.com/ML2410manual

Limited Warranty

MTRLC LLC warrants this production against defects in cloth and workmanship for a warranty menstruation of 2 years. To read the full warranty, please go to www.motorolanetwork.com/warranty

Safety Precautions

These precautions assist protect you and your ML2410.
This equipment is designed with the utmost care for the safety of those who install and apply it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacturer must therefore be immune at all times to ensure the safe apply of the equipment.

Do not put the ML2410 or its power cube in water, since this is a shock run a risk.
Protect the ML2410 from moisture and be careful nigh temperature.
Your ML2410 should be operated in an environment that's between 32 and 104° Fahrenheit (0 to 40° Centigrade).
Your ML2410 should not be in a bars space. In that location should exist room for airflow around the top, front, and sides of the ML2410.
Make certain to employ your ML2410's power adapter and a compatible electrical outlet.

MOTOROLA and MTRLC presume no liability for damage caused by whatever improper utilize of the router.
Label Symbols

SYMBOL	INDICATES
	DC voltage
	AC voltage
	For indoor use only
	Class II equipment
	Energy Efficiency Marking
	Center-positive power input polarity

FCC Statement

This device complies with Class B Office fifteen of the FCC Rules. Performance is discipline to the post-obit two atmospheric condition: (one) this device may non crusade harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection confronting harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Withal, there is no guarantee that interference will not occur in a detail installation. If this equipment does cause harmful interference to radio or television reception, which tin can exist determined past turning the equipment off and on, the user is encouraged to try to right the interference by one or more of the following measures: reorient or relocate the receiving antenna, increase the separation between the equipment and receiver, connect the equipment into an outlet on a circuit unlike from that to which the receiver is connected, and/or consult the dealer or an experienced radio/Television receiver technician for assist.
FCC Circumspection: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This transmitter must not exist co-located or operating in conjunction with any other antenna or transmitter. For operation within the 5.fifteen – five.25GHz frequency range, it is restricted to indoor functioning. This device meets all the other requirements specified in Part 15E, Department 15.407 of the FCC Rules.
FCC Radiations Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated within a minimum distance of 38 cm between the radiator and your trunk.

MTRLC LLC PO Box 121147 Boston, MA 02112-1147
©MTRLC LLC 2022. MOTOROLA and the Stylized Thou Logo are trademarks or;
registered trademarks of Motorola Trademark Holdings, LLC. and are used under license.
All other trademarks are the belongings of their corresponding owners. All rights reserved.
27797-EL-A/0950

Documents / Resources

References

Source: https://manuals.plus/motorola/ac1900-wifi-router-ml2410-manual